Miele CSZL 400 Datový list

Installation instructionsGas-hobKM 404 / KM 405KM 406KM 414 / KM 417It is essential to read theseinstructions before installingor using the machine, t

KM 417a Support bracketb Building in height plus 3 mm for fixing screwc Frontd Building in height - Mains connection boxe Gas connectionAppliance dime

Before installing the appliance check that the location provides the requiredclearances from combustible materials and if necessary provide protection

Clearance above and aroundthe appliancea Range hoodb not less than 650 mm from burner toany horizontal surface over full widthof the appliance.c Burne

Dimensions 7 mm and 11 mm are thespace taken up by the frame of theappliance on the worktop.^ Make a cut-out for the hob in theworktop, paying attenti

Fitting the spacer bars andsupport bracketsa Support bracketsb Spacer barsThe illustration above shows anexample of a worktop cut-out withspacer bars

Fixing the spacer bar^ Position the spacer bars b in thepositions shown in "Fitting the spacerbars and support brackets" so theyare flush wi

Fixing the support brackets^ Position the two support bracketssupplied a in the positions shown in"Fitting the spacer bars and supportbrackets&qu

Dimensions 7 mm and 11 mm are thespace taken up by the frame of theappliance on the worktop.^ Make a cut-out for the hob in theworktop.Dimension "

Fitting the spacer bars andsupport bracketsKM 414 / KM 417with 2 appliances 288 mm wide b Support bracketsa Support bracketsb Spacer barsInstallation

Fixing the spacer barThe spacer bar is only required whencombined with a 288 mm widecombiset appliance.^ Position the spacer bars b in thepositions sh

Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Building in . . . . . . . . . . . . . . . .

Fixing the support brackets^ Position the two support bracketssupplied a in the positions shown in"Fitting the spacer bars and supportbrackets&qu

ImportantUnder no circumstances shouldsealant find its way between theframe of the top part of the hob andthe worktop.This could cause difficulties if

All electrical work should be carriedout by a suitably qualified andcompetent person in strictaccordance with national and localsafety regulations.For

Connection to the gas supply, orconversion from one type of gas toanother should only be undertaken byan approved fitter, who is responsiblefor correc

The gas connection must be inaccordance with national and localregulations.The relevant building regulationsmust also be observed.KM 404 / KM 405 / KM

KM 404When converting to liquid gas, themain jets and the small jets of allburners must be changed.Nominal rating for all gas types withthe burner ful

Changing the jetsDisconnect the gas hob from theelectricity supply. Depending on thetype of installation, either withdrawthe mains fuse, switch off at

KM 405When converting to liquid gas, themain jets and the small jets of allburners must be changed.Nominal rating for all gas types withthe burner ful

Changing the jetsDisconnect the gas hob from theelectricity supply. Depending on thetype of installation, either withdrawthe mains fuse, switch off at

KM 406When converting to liquid gas, themain jets and the small jets of allburners must be changed.Nominal rating at high settingGas type MJ/hBurner N

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Electrical connection . .

Changing the jetsDisconnect the gas hob from theelectricity supply. Depending on thetype of installation, either withdrawthe mains fuse, switch off at

Changing the main jet^ With a 10 mm socket spanner, loosenthe main jet from its holder, turninganti-clockwise, at the same time usea 13 mm spanner to

Changing the jet for the inner burnerd jet disc (main jet for the inner burner)e air sleevef air vent^Remove screw c from the fitting bwith an 8 mm sp

Check the first intake of aira Securing screwb Air sleeveGap "X" must measure:13 mm for Natural gas13 mm for Liquid gas^If this is not the c

KM 414When converting to liquid gas, themain jets and the small jets of allburners must be changed.Nominal rating for all gas types withthe burner ful

Changing the jetsDisconnect the gas hob from theelectricity supply. Depending on thetype of installation, either withdrawthe mains fuse, switch off at

KM 417When converting to liquid gas, themain jets and the small jets of allburners must be changed.Nominal rating for all gas types withthe burner ful

Changing the jetsDisconnect the gas hob from theelectricity supply. Depending on thetype of installation, either withdrawthe mains fuse, switch off at

38

39

Building inFit wall units and the cooker hoodbefore fitting the appliance, to avoiddamaging it.As a minimum 20 m3space isrequired where the appliance

Alteration rights reserved / 0903This paper consists of cellulose which has been bleached without the use of chorineM.-Nr. 05 021 252 / 01

The gas hob must not be installednext to an electric fryer, as the gasflames could ignite fat in the fryer. It isessential to maintain a minimumdistan

KM 404a Support bracketb Building in height plus 3 mm for fixing screwAppliance dimensions6

KM 405a Support bracketb Building in height plus 3 mm for fixing screwc Frontd Building in height - Mains connection boxe Gas connectionAppliance dime

KM 406a Support bracketb Building in height plus 3 mm for fixing screwAppliance dimensions8

KM 414a Support bracketb Building in height plus 3 mm for fixing screwAppliance dimensions9