Miele GAS COMBISET CS 1011 Provozní pokyny

Operating and installation instructionsGas cooktopsCS 1011To avoid the risk of accidents ordamage to the appliance it isessential to read theseinstruc

Technical safety~Installation, maintenance andrepairs may only be carried out by asuitably qualified and competentperson in strict accordance with cur

~While the appliance is underguarantee, repairs should only beundertaken by a service technicianauthorised by the manufacturer.Otherwise the guarantee

~Pans must be the correct size for theburner they are used on (see "Pans"). Apan which is too small will be unstableon the pan support. If t

~Replace the pan supports carefullyto avoid scratching the surface of thecooktop.~Using the gas cooktop will cause abuild-up of heat and moisture in t

Disposal of the packingmaterialThe transport and protective packinghas been selected from materials whichare environmentally friendly for disposaland

Please adhere the extra data plate forthe appliance supplied with thisdocumentation in the space provided inthe "After sales service" sectio

Rapid ignition systemThe appliance is supplied with a rapidignition system with the followingfeatures:–The control knob can be released assoon as the

Switching on,Do not leave the applianceunattended whilst it is being used.^To ignite the burner push the controlknob down and turn it anti-clockwiseto

In-operation indicator andResidual heat indicatorWhen the gas cooktop is switched on,the in-operation indicator lights up.Once it has reached a certai

Min. base diameterPots/pans=15cmMax. rim diameterPots/pans=24cm–Wide, shallow pans are preferable totall, narrow ones. They will heat upfaster.– Pans

WO This appliance can be used in countries other than those specified onthe appliance. It is, however, set up for connection to the gas and electricit

Thermo-electric ignitionThis appliance has a thermo-electricignition safety device. If the flame goesout, for example if food has boiled overor if the

General notes,Under no circumstances use asteam cleaning appliance to cleanthis appliance. The steam couldattack the electrical componentsand cause a

Stainless steel surfacesClean stainless steel surfaces using asolution of warm water and a smallamount of washing-up liquid appliedwith a soft sponge.

BurnerDo not clean any parts of the burnerin a dishwasher.The burner should be dismantled andthen cleaned by hand using a solutionof warm water and a

,Repairs to the gas and electricalcomponents of this appliance mustonly be carried out by a suitablyqualified and competent person toensure safety. Re

... the gas flame suddenly looksdifferent.Check whether the burner componentsare assembled correctly... the gas flame goes out duringoperation.Check

Miele branded cleaning and conditioning products areavailable for your appliance.These can be ordered via the internet atwww.miele-shop.com (depending

Fit wall units and rangehood beforefitting the cooktop to avoiddamaging the surface.~This appliance must not beconnected to a gas flue. It must beinst

Safety clearance above the cooktopA minimum safety clearance must bemaintained between the cooktop andthe rangehood above it. See therangehood manufac

Before installing the appliance checkthat the location provides the requiredclearances from combustible materialand if necessary provide protection to

Guide to the appliance ...5Cooktop ...5Accessories su

a Spring clampsb Frontc Building-in depthd Mains connection box with mains connection cable, L = 2,000 mme Gas connection R 1/2 - ISO 7-1Appliance and

^Make the worktop cut-out followingthe dimensions applicable.Remember to maintain a minimumsafety clearance from the back wall,as well as from any tal

When installing two or more appliances next to each other a spacer bar b mustbe used between each one.See "Fitting the spacer bars and support br

Worktop cut-out calculation example for three appliancesAAppliance widthless 8BAppliancewidthCAppliance widthless 8DWorktopcut-out280 288 280 848280 3

a Spring clampsb Spacer barsc Gap between spacer bar and worktopThe illustration shows a worktop cut-out with spring clamps a and spacer bars bfor 3 a

Wooden worktops^Position the spring clamps supplieda and spacer bars b on the topedge of the cut-out in the positionsmarked.^Secure the spring clamps

^Coat the side edges and the loweredges of the spring clamps withsilicone.^Then fill gap d between the spacerbars and the worktop with siliconefrom th

Installing the appliance^Feed the connection cable downthrough the cut-out.^Then drop the front edge of theappliance into the cut-out.^Using both hand

Do not use sealant between theframe of the top part of theappliance and the worktop.This could cause difficulties if theapplinace ever needs to be tak

All electrical work should be carriedout by a suitably qualified andcompetent person in strictaccordance with national and localsafety regulations.If

Installation of several appliances...32Fixing the spring clamps and spacer bars ...35Install

Connection to the gas supply, orconversion from one type of gas toanother should only be undertakenby an approved gas fitter, who isresponsible for co

The gas connection must be inaccordance with national and localregulations.The relevant building regulationsmust also be observed.Natural gas / liquid

,Connection to the gas supply, orconversion from one type of gas toanother, should only be undertakenby an approved and registered gasinstaller in str

Changing the jetsDisconnect the gas cooktop fromthe electricity supply by switchingoff at the socket and withdrawing theplug or by disconnecting the m

To change the jet for the inner burnerd Jet disc (main jet for the innerburner)e Air intake sleevef Vent^Whilst counterholding it in place withan SW 1

To check the first intake of aira Retaining screwb Air intake sleeveGap X must measure:For natural gas: 13 mmFor liquid gas: 13 mmIf it doesn't:^

To change the small jetsa Small diameter jet(e.g. for liquid gas: 0.25)b Large diameter jet(e.g. for liquid gas: 0.68)^Using a small screwdriver, unsc

After changing the jets^Reassemble the burner parts in thereverse order.^Check all gas fittings for leaks byoperating the burner without theupper sect

The address of the nearest Miele Customer Contact Centre is given on the backpage.The voltage and rated load are given on the data plate. Please quote

49

Cooktopa Wok burnerb Pan supportc Control knobd DisplayDisplaye In-operation indicatorf Residual heat indicatorGuide to the appliance5

50

51

Alteration rights reserved/ 5108M.-Nr. 07 235 550 / 02

Burnerg Inner burner caph Outer burner capi Burner ringj Burner headk Ignition safety devicel Ignitorm Burner baseGuide to the appliance6

Accessories suppliedThe accessories supplied with your CombiSet appliance as well as a range ofoptional ones are available to order (see "Optiona

This appliance complies with allrelevant local and national safetyrequirements. Improper use of theappliance can, however, present arisk of both perso

Safety with children~Children should be supervised toensure that they do not play with theappliance.~Older children may use theappliance only when its